IDACT 3.0-6

Version Update 3.0-6

Infolock is pleased to announce the immediate release of IDACT (INSIGHT DLP Appliance Configuration Tool) version 3.0-5. This release provides the following:

  1. New feature enhancements and bug fixes.
  2. Support for Symantec DLP v15.8.0
  3. Stability improvements.
  4. An update for the IDACT OS on the INSIGHT appliance, Enforce, and all running Linux detection servers.

Important Notes

  1. The INSIGHT Web UI services must be enabled and running before this IDACT update.
  2. Verify that all servers (Appliances and SDLP VMs) have internet access to over ports 80 (default) or 443. If you plan to use port 443 for IDACT updates, please review Update Repo from port 80(http) to 443(https)
  3. If using a proxy, please verify the below files on each host and VM is configured correctly:
    1. /etc/yum.conf
    2. /etc/wgetrc
  4. It is recommend that after every IDACT update the Appliance and SDLP VMs be restarted/rebooted.


Release Scope

This release will only update the underlying OS and IDACT software - it will not upgrade your DLP release. If you require a DLP release upgrade on your INSIGHT appliance, please find the latest Upgrade Guide version within the support portal at  INSIGHT 15.8.0 Upgrade Guide.


Before Upgrading Symantec DLP or IDACT Firmware

We strongly recommend you check the INSIGHT DLP Appliance Support Matrix before attempting to upgrade the Symantec DLP software and/or the INSIGHT DLP Appliance IDACT firmware. This is to determine if the desired version is supported on your appliance model.

Failure to abide by the supportability matrix may put your INSIGHT DLP Appliance into an unsupported configuration, resulting in incompatibility-related issues or failures.


We strongly recommend you read this article on the new feature "Archive Backup". Please take note of your current backup settings as you will be required to reconfigure your backup time and schedule after this update is applied, prior to utilizing the Archive Backup process. Failure to reconfigure the backup time and schedule will simply result in the System Backup section of the Appliance WebUI to remain blank until you update it with your previous or new backup info. If you have any questions please feel free to contact INSIGHT Support team.


To Update the IDACT Version

A. Via SSH:
*When using SSH to do updates you will be able to see output of running updates and related errors.

  1. Log into each Infolock INSIGHT DLP Appliance via SSH as Appuser.
  2. Issue the following command: update
  3. Issue the following command again: update
    For this current version please run "update" twice

or B. Via Appliance WebUI:
*When using Appliance WebUI to do updates you will not see output of running update.

  1. Log into each Infolock INSIGHT DLP Appliance WebUI as Appuser.
  2. Navigate to the "Device List" page
  3. Select: update
    *Please allow up to 30 minuses for this first update to complete before executing it again.
  4. Select: update
    *For this current version please run "update" twice


*If there are any errors or warnings please re-run "update"

* It is recommend that you run to fix any kernel issues on all Appliances and VMs (Enforce and Detection servers). See section "After Updating" below for more details.

*If the Appliance Web UI does not start after the update, please reboot the Appliance host. Please see below.


After Updating

A. It is recommended that you run the below to fix any kernel issues, on all Appliances and VMs (Enforce and Detection servers):

As a protect user on the appliance:
OR As appuser on the VMs (Enforce and Detection servers):
Run sudo /opt/appliance/   Run sudo /opt/appliance/


B. It is recommended to always restart/reboot after every IDACT update. Please reboot the Appliance host and all running SDLP servers via the Appliance WebUI or SSH.

As appuser via Appliance WebUI
Navigate to Device List and select server then select restart

================= OR =================

As appuser via SSH to the Appliance
AND As appuser via SSH to Enforce and Detection server VMs
Run restart Appliance
Run sudo shutdown -r now


C. If the Appliance Web UI does not start after the update, please reboot the Appliance host or log into it via SSH and take the following action. 

As appuser OR As protect user
Run service_restart Run sudo service appliance-web restart


D. You must reconfigure your Enforce backups after this update as the new Backup Archive feature zeros out the old settings. Please follow the steps in this article:


Obtaining Support

If you require technical assistance with this issue, have any questions, or require further information, please contact the Infolock Support Team at or via


Infolock Support Team


IDACT 3.0-5 Change log:

- Minor update

- Added new feature Terms and Condition. Article:

- Updated to allow customers to received email notifications for disk management. Article:
- Added Archive Backup to Appliance WebUI, to allow customers to offload backups to another INS Appliance Enforce. Article:


- Minor update

- Updated Oracle DB 12c patching script and Oracle DB 19c patching script Article:
- Added Oracle 12c to 19c upgrade script Article:

- Minor update




Was this article helpful?
0 out of 0 found this helpful
Have more questions? Submit a request


Article is closed for comments.